NBR vs EPDM vs Viton Which Seal Elastomer Is Best for Your Application
A mechanical seal can fail even when the faces, springs, and hardware are correctly selected. Often, the weak point is the elastomer. The O-ring, wedge, cup, boot, or gasket must handle the fluid, temperature, pressure, and cleaning conditions around the seal. If the elastomer swells, hardens, cracks, or loses compression, leakage follows.
That is why NBR vs EPDM vs Viton is such a common comparison in pump and equipment maintenance. These three materials cover many industrial sealing needs, but they are not interchangeable. NBR performs well in oils and fuels. EPDM handles water, steam, and many polar chemicals. Viton, also known as FKM, is selected for higher temperature and stronger chemical resistance.
The right choice reduces leakage, downtime, and repeat purchasing. The wrong choice can make even a well-made mechanical seal fail early.

Why elastomer selection matters in mechanical seals
Mechanical seal elastomers do more than fill a gap. They maintain compression, compensate for small movement, and stop leakage paths around the seal faces and shaft sleeve. In pumps, agitators, mixers, reactors, and process equipment, they may come in contact with:
Process liquid
Vapour or gas phase
Flush or quench fluid
Cleaning chemicals
Heat from friction or process temperature
Abrasive particles or crystallising media
A seal may be mechanically correct but chemically wrong. For example, an EPDM rubber seal may work well in hot water service but fail quickly in mineral oil. An NBR rubber seal can handle lubricating oil, but it is usually a poor choice for ozone-rich outdoor exposure. A Viton O-ring can tolerate many aggressive fluids, but it is not the best answer for every solvent, amine, or hot caustic duty.
The practical goal is simple: match the elastomer to the actual operating conditions, not just the pump model.
NBR, EPDM, and Viton compared at a glance
The table below gives a useful starting point for O-ring material selection. Always verify final compatibility against the exact chemical concentration, temperature, pressure, and compound grade.
Property | NBR | EPDM | Viton or FKM |
Common name | Nitrile rubber | Ethylene propylene diene monomer | Fluoroelastomer |
Typical strength | Oils, fuels, grease, hydraulic fluids | Water, steam, glycol, many dilute acids and alkalis | Oils, fuels, solvents, many chemicals, high temperature |
Typical weakness | Ozone, sunlight, weathering, ketones, some solvents | Petroleum oil, fuels, mineral oils | Steam, hot water, amines, some ketones, hot caustic |
General temperature capability | Moderate | Good, especially for water and steam service | High |
Cost level | Usually economical | Usually economical to moderate | Usually higher |
Common use | Oil pumps, fuel systems, hydraulic equipment | Water pumps, chemical cleaning lines, food and pharma utilities | Chemical pumps, petrochemical service, high-temperature oil duties |
This table should not replace an elastomer compatibility chart, but it helps narrow the choices before a detailed check.
When NBR is the right seal elastomer
NBR, or nitrile rubber, is one of the most widely used mechanical seal O-ring materials. It is often the standard choice for general oil, grease, and fuel service because it gives a good balance of cost, availability, and performance.
NBR is commonly used in:
Lubricating oil pumps
Diesel and fuel transfer pumps
Hydraulic systems
Gearbox and compressor lubrication systems
General industrial pumps handling non-aggressive hydrocarbons
NBR has good resistance to many petroleum-based fluids. It also offers decent abrasion resistance and compression set performance when the compound is properly chosen.
Where NBR performs well
NBR is a practical choice when the sealing fluid is oil-based and temperatures remain within a moderate range. For maintenance teams and pump repair companies, this makes NBR a familiar option for many standard replacement mechanical seals.
It is also easy to source in common sizes, which helps when downtime is critical. In many cases, NBR gives the lowest total cost when the media are suitable.
Where NBR should be avoided
NBR is weak against ozone, sunlight, and weathering unless specially compounded. It is also not ideal for many ketones, esters, chlorinated solvents, and strong oxidising chemicals.
If the pump handles hot water, steam, acids, alkalis, or cleaning chemicals, do not assume NBR will work. Check the actual fluid data. NBR can swell or soften in the wrong chemical environment, leading to loss of sealing force and leakage.
For a simple comparison, Viton vs NBR often comes down to chemical severity and temperature. NBR is economical for compatible oils. Viton is preferred when the service is hotter or chemically more demanding.
When EPDM is the right seal elastomer
EPDM is a strong choice for water-based and polar fluids. It is widely used in utilities, cleaning systems, and process applications where resistance to hot water, steam, glycols, and many dilute chemicals is needed.
EPDM is commonly used in:
Hot and cold water pumps
Boiler feed and condensate-related systems, depending on conditions
CIP and cleaning lines
Glycol circulation systems
Mild acid and alkali services
Some food and pharmaceutical utility applications
EPDM offers good resistance to weathering, ozone, and ageing. This gives it an advantage in outdoor or exposed applications where NBR may crack over time.
Where EPDM performs well
EPDM is often the better choice for water, steam, and non-oil-based chemical service. It can handle many polar fluids that cause problems for nitrile. In industries where cleaning cycles involve hot water or diluted cleaning solutions, EPDM can be a reliable option when the chemical list is compatible.
When comparing NBR vs EPDM, the first question is often whether the media are oil-based or water-based. Oil service usually points towards NBR. Water, steam, glycol, and many cleaning fluids often point towards EPDM.
Where EPDM should be avoided
EPDM should not be used with petroleum oils, mineral oil, diesel, petrol, and many hydrocarbon-based fluids. In those services, EPDM can swell heavily and lose its sealing properties.
This is why EPDM is not a universal upgrade from NBR. It is better in some chemical families and worse in others. For procurement teams, the part description alone is not enough. The service fluid must be known.
When comparing EPDM vs Viton, EPDM is often better for hot water and steam, while Viton is usually better for oils, fuels, and many solvents. The final choice depends on the exact duty.

When Viton or FKM is the right seal elastomer
Viton is a well-known trade name for FKM fluoroelastomers. In industry, many buyers use “Viton” and “FKM” together, though the exact compound and brand can vary. An FKM mechanical seal is often selected when the application involves higher temperature, aggressive chemicals, oils, fuels, or solvents.
Viton is commonly used in:
Chemical transfer pumps
Petrochemical and refinery equipment
Solvent handling systems
High-temperature oil circulation
Hydrocarbon processing
Selected acids and aggressive chemical duties
Viton offers excellent resistance to many oils, fuels, and hydrocarbon solvents. It also has better high-temperature capability than standard NBR and EPDM in many dry or oil-based services.
Where Viton performs well
Viton is often chosen when a basic elastomer is not enough. It is one of the most common chemical resistant seal materials for demanding pump services. It can resist swelling and chemical attack in many fluids where NBR or EPDM would not last.
For a rubber seal for chemical pumps, Viton may be the right choice when the chemical is compatible and the operating temperature is high. It is also useful where process conditions vary and a wider resistance range is needed.
Where Viton should be avoided
Viton is not suitable for every aggressive fluid. It can perform poorly in steam, hot water, amines, some ketones, and hot caustic solutions. Low-temperature flexibility can also be weaker than some other elastomers.
Cost is another factor. Viton usually costs more than NBR or EPDM. If the service is simple water, mild chemical, or compatible oil at moderate temperature, another elastomer may give better value.
How to choose the right elastomer for replacement mechanical seals
When selecting elastomers for a new or replacement seal, avoid choosing only by colour, old material, or what was previously installed. The previous seal may have failed because the elastomer was wrong.
Use this practical selection method.
Identify the exact media
Get the full chemical name, concentration, and any additives. “Solvent”, “acid”, “oil”, or “chemical” is not enough. A small change in concentration or blend can change compatibility.
For mixed media, check every component. Also check cleaning fluids, flushing fluids, and occasional contamination.
Check the real operating temperature
Do not use only ambient temperature. Consider process temperature, heat generated at the seal faces, dry running risk, and cleaning temperature.
A material that is compatible at room temperature may fail at higher temperature. This is especially important in chemical, pharmaceutical, and food-processing plants where cleaning cycles may be hotter than normal production.
Review pressure, movement, and seal design
Elastomers in mechanical seals face compression, shaft movement, vibration, and sometimes vacuum. A static gasket and a dynamic O-ring do not see the same stress.
Seal design also matters. Pusher seals, bellow seals, cartridge seals, and component seals may place different demands on the elastomer.
Compare compatibility before price
Price matters in procurement, but premature failure costs more than the difference between elastomers. A lower-cost O-ring can become expensive if it stops production or damages the seal faces.
Use compatibility data as the first filter. Then compare availability, lead time, and cost.
Share application details with the seal manufacturer
For replacement seals, a good manufacturer needs more than dimensions. Share:
Pump or equipment type
Shaft size and seal chamber details
Fluid name and concentration
Operating temperature and pressure
Speed
Existing seal drawing or sample
Failure pattern, such as swelling, hardening, cracking, or leakage
Lova-Tech Industries, an ISO 9001:2015 certified mechanical seal manufacturer based in Gujarat, India, manufactures standard and custom replacement mechanical seals for pumps, agitators, mixers, reactors, and other industrial equipment. For replacement jobs, the team can work from drawings, samples, or customer specifications and help match the elastomer to the actual service conditions.
This is especially useful when the old seal has an unknown O-ring material or when the application has changed after installation.
Common selection mistakes to avoid
Many elastomer failures come from simple assumptions. These are the ones to watch.
Using NBR for all general-purpose pumps
NBR is common, but it is not universal. It works well in compatible oil-based media, not in every chemical or water-based system.
Using EPDM because the service contains water
EPDM may suit water and steam, but mixed fluids can contain oils, solvents, or additives that attack it. Always check the full composition.
Using Viton as the automatic premium option
Viton is strong, but not always correct. In steam or hot caustic service, another material may perform better.
Ignoring cleaning and flushing fluids
The process liquid may be compatible, while the cleaning chemical destroys the elastomer. This is common in food, pharmaceutical, and chemical plants.
Replacing by colour
O-ring colour is not a reliable material standard. Different suppliers may use different colours, and black O-rings can be NBR, EPDM, FKM, or other materials.
A practical selection guide
Use this quick guide as a first filter before checking detailed compatibility.
Application condition | Likely starting choice | Reason |
Mineral oil, grease, diesel, hydraulic oil | NBR or FKM | NBR is economical. FKM suits higher temperature or harsher service |
Hot water, steam, glycol | EPDM | Strong resistance to many water-based and polar fluids |
Petroleum solvents or fuels at higher temperature | FKM | Better chemical and heat resistance than standard NBR |
Outdoor exposure with water service | EPDM | Good ozone and weather resistance |
Strong chemical pump application | FKM or other specialist elastomer | Check the exact chemical and temperature |
Unknown chemical mixture | Do not guess | Confirm compatibility before ordering |
This guide is useful for shortlisting, but it does not replace compound-level verification. The best O-ring material selection combines chemical compatibility, temperature, seal design, and operating history.
Final takeaway
NBR, EPDM, and Viton each solve different sealing problems.
Choose NBR for many oil, grease, fuel, and hydraulic applications where conditions are moderate. Choose EPDM for water, steam, glycol, and many polar chemical services where petroleum oils are not present. Choose Viton or FKM for many high-temperature, oil, fuel, solvent, and chemical duties where the media are compatible.
The best elastomer is not the most expensive one. It is the one that stays stable in the actual fluid, at the actual temperature, inside the actual mechanical seal. For plants, pump repair teams, and equipment manufacturers, that careful selection can mean fewer leaks, fewer repeat failures, and longer seal life.




Comments